FY 09-10

1. Application of liquid/solid fluidization technique in beneficiation of fines;
   A K Mukherjee, B K Mishra, R V Kumar; International Journal of Mineral Processing; Vol. 92 (2009); pp. 67-73

2. Influence of chemical parameters on selectivity and recovery of fine coal through flotation;
   A K Gupta, P K Banerjee and A Mishra; International Journal of Mineral Processing; Vol. 92 (2009); pp. 1-6

3. A new method for evaluation of gravity separation processes;
   A K Mukherjee; Mineral Processing and Extractive Metallurgy Review; Vol. 30, Issue 3 (2009); pp. 191-210

4. Liquids/solid fluidization its role and limitation in fine beneficiation – a review;
   A K Mukherjee and A Kumar; Mineral Processing and Extractive Metallurgy Review; Vol. 30, Issue 3 (2009); pp. 280-306

5. Heat and mass transfer study in fluidized bed granulation –prediction of entry length;
   P Roy, M Vashishthaa, R Khanna and D Subbarao; Particuology; Vol. 7 (2009); pp. 215-219

6. Effect of variation of alumina on the microhardness of iron ore sinter phases;
   M Sinha and R V Ramna; ISIJ International; Vol. 49, Issue 5 (2009); pp. 719-721

7. CFD simulation of influence of superficial gas velocity column size, spurger arrangement and taper angle on hydrodynamics of the column flotation cell;
   D Chakraborty, M Guha and P K Banerjee, Chemical Engineering Communications; Vol. 196 (2009); pp. 1102-1116

8. Characterization and pre-concentration of chromite values from plant tailinmgs using floatex density separator;
   C R Kumar, S Tripathy and D S Rao; Journal of Minerals and Materials Characterization; Vol. 8, Issue 5 (2009); pp. 367-378

9. Metallurgical use of heat altered coal: a case study;
   D Nag, A K Singh and P K Banerjee; Journal of Minerals and Materials Characterization; Vol. 8, Issue 7 (2009); pp. 541-549

10. Prediction of coke CSR from ash chemistry of coal blend;
    D Nag, S K Haldar, P K Choudhary and P K Banerjee; International Journal of Coal Preparation and Utilization; Vol. 29, Issue 5 (2009); pp. 243-250

11. Effect of manganese ore blends on performance of submerged arc furnace for ferromanganese production;
    V Tathavadkar, V Singh, P K Mishra, P Mallick and B D Nanda; Ironmaking and Steelmaking; Vol. 37, Issue 2 (2010); pp. 103-111

12. Hydrodynamic characteristics of a sparged gas-liquid contactor for fine bubble generation;
    D Chakraborty, G S R Krishna, S Chakraborty and B C Meikap; Indian Engineering Chemical Research; Vol. 48 (2009); 11225-11229

13. Connectionist approach for modeling the dry roll magnetic separator;
    V Singh; Minerals and Metallurgical Processing; Vol. 26, Issue 3 (2009); pp. 127-132

14. Selective classification of mineral sand slimes in an air fluidized bed;
    V Singh and S M Rao; Mineral Processing and Extractive Metallurgy Review; Vol. 31, Issue 2 (2010); pp. 59-72

15. Petrographic characteristics of coal from Lati formation, Tarakan basin, East Kalimantan, Indonesia;
    P K Singh, M P Singh, A K Singh and M Arora; International Journal of Coal Geology; Vol. 81 (2010); pp. 109-116

16. Formation and magnetic behavior of manganese oxide nanoparticles;
    S Thotaa, B Prasad and J Kumar; Materials Science and Engineering B; Vol. 167, Issue 3 (2010); pp. 153-160

17. Evolution of bubble size distribution in baked foods;
    P Deshlara, A Mehra and D Ghosal; Journal of Food Engineering; Vol. 93, Issue 2 (2009); pp. 192-199

18. Quantification of the solidification microstructure in continuously cast high carbon steel billets;
    S Ganguly and S K Choudhary; Met Trans B; Vol. 40 (2009); pp. 97-104

19. Development of material trajectory simulation model for blast furnace bell-less top;
    S Nag and V M Koranne; Ironmaking and Steelmaking; Vol. 36, Issue 5 (2009); pp. 371-378

20. Optimization of electromagnetic stirring in steel billet caster by using image processing technique for improvement in billet quality;
    P P Sahoo, A Kumar, J Halder and M Raj; ISIJ International; Vol. 49, Issue 4 (2009); pp. 521-528

21. Membrane contactor as degasser operated under vacuum for ammonia removal from water: a numerical simulation of mass transfer under laminar flow conditions;
    A Mandowara and P K Bhattacharya; Computers and Chemical Engineering; Vol. 6 (2009); pp. 1123-1131

22. Heat transfer in nucleate pool boiling of aqueous SDS and triton X-100 solutions;
    V M Wasekar; Heat and Mass Transfer; Vol. 45 (2009); pp. 1409-1414

23. A static approach towards coke collapse modeling in blast furnace;
    S Nag, S Basu and A B Yu; Ironmaking and Steelmaking; Vol. 36, Issue 7 (2009); pp. 509-514

24. Optimization of dual purging location for better mixing in ladle: a water model study;
    K Chattopadhyaym A Sengupta, S K Ajmani, S N Lenka and V Singh; Ironmaking and Steelmaking; Vol. 36, Issue 7 (2009); pp. 537-542

25. Experimental investigation of the effective electrical conductivity of aluminium oxide nanofluids;
    S Ganguly, S Sikdar and S Basu; Powder Technology; Vol. 196, Issue 3 (2009); pp. 326-330

26. A mathematical model to optimize aluminium wire injection in steel melts;
    S Sanyal, J K Saha and S Chandra; Steel Research International; Vol. 80, Issue 8 (2009); pp. 559-567

27. Mathematical model for prediction of composition of inclusions formed during solidification of liquid steel;
    S K Choudhury and A Ghosh, ISIJ International; Vol. 49, Issue 12 (2009); pp. 1819-1827

28. Melt-conditioned, high pressure die casting of Mg-Zn-Y alloy;
    M Xia, S Mitra, B Dhindaw, G Liu and Z Fan; Met Trans B; Vol. 41B (2010); pp. 209-213

29. A novel bottom stirring scheme to improve BOF performance through mixing and mass transfer modeling;
    V Singh, S N Lenka, S K Ajmani, C Bhanu and S Pathak; ISIJ International; Vol. 49, Issue 12 (2009); pp. 1889-1894

30. Optimal configuration of blast furnace slag runner to reduce fluid flow stresses at wall using mathematical modeling;
    A Kumar, S K Ajmani and A R Pal; Ironmaking and Steelmaking; Vol. 37, Issue 1 (2010); pp. 9-14

31. Strength assessment of spot-welded sheets of interstitial steels;
    G Mukhopadhyay, S Bhattacharya and K K Ray; Journal of Materials Processing Technology; Vol. 209 (2009); 1995-2007

32. Effect of pre-strain on the strength of spot-weld;
    G Mukhopadhyay, S Bhattacharya and K K Ray; Materials and Design; Vol. 30 (2009); pp. 2345-2354

33. Effect of strip temperature on the formation of an Fe2Al5 inhibition layer during hot-dip galvanizing;
    M Dutta and S B Singh; Scripta Materialia; Vol. 60 (2009); pp. 643-646

34. Premature failure of aluminium core steel reinforced wires;
    A Chattopadhyay and D Mishra; Engineering Failure and Analysis; Vol. 16, Issue 5 (2009); pp. 1734-1739

35. Neural network model of the profile of hot rolled strip;
    S Sikdar and S Kumari; International Journal of Advanced Manufacturing Technology; Vol. 42 (2009); pp. 450-462

36. Study of formation of “easy to remove oxide scale” during mechanical descaling of high carbon wire rods;
    A Chattopadhyay, P Kumar and D Roy; Surface and Coatings Technology; Vo. 203 (2009); pp. 2912-2915

37. Studies on hot rolled galvanized steel sheets: effect of reheating on galvanizing;
    A Chattopadhyay, V S Sarma, B S Murty, A Haldar and D Bhattacharjee; Surface and Coatings Technology; Vol. 203 (2009); pp. 3465-3471

38. Prediction of transformation texture under complex rolling condition;
    S Kundu; Materials Science and Engineering A; Vol. 516A (2009); pp. 290-296

39. Effect of dynamic contact resistances on advanced high strength steels under medium frequency DC spot welding conditions;
    M Shome; Science and Technology of Welding and Joining; Vol. 14, Issue 6 (2009); pp. 533-541

40. Effects of composition and processing parameters on precipitation and texture formation in microalloyed interstitial free high strength (IFHS) steels;
    R K Ray, P Ghosh and D Bhattacharjee; Materials Science and Technology; Vol. 25, Issue 9 (2009); pp. 1154-1168

41. Precipitation in interstitial free high strength steel;
    P Ghosh, C Ghosh and R K Ray; ISIJ International; Vol. 49, Issue 7 (2009); pp. 1080-1086

42. Evaluation of formability and mechanical behavior of laser-welded tailored blanks made of interstitial-free and dual-phase steels;
    S Chatterjee, R Saha, M Shome and R K Ray; Met Trans A; Vol. 40 A (2009); pp. 1142-1152

43. Influence of microstructure and texture on the formability character of industrially produced galvannealed coatings on three interstitial free steels;
    A Chakraborty and R K Ray; Surface and Coatings Technology; Vol. 203 (2009); pp. 1756-1764

44. Characterization of industrially produced galvannealed coating using cross sectionals specimen in TEM;
    A Chakraborty, R Saha and R K Ray; Materials Characterization; Vol. 60 (2009); pp. 882-887

45. Optimization of galvannealing parameters through numerical modeling of galvannealing process;
    A K Verma, S Chandra, N Bandyopadhyay, B K Dhindaw and R D K Mishra; Met Trans A; Vol. 40A (2009); 1153-1159

46. Effect of material properties on contact resistance and nugget size during spot welding of low carbon coated steels;
    M Shome and S Chatterjee; ISIJ International; Vol. 49, Issue 9 (2009); pp. 1384-1391

47. On the Cu precipitation behavior in thermodynamically processed low carbon microalloyed steels;
    S K Ghosh, A Haldar and P P Chattopadhyay; Materials Science and Engineering A; Vol. 519, Issue 1-2 (2009); pp. 88-93

48. Development of texture, microstructure and grain boundary character distribution in a high strength boron-added interstitial-free steel after severe cold rolling and annealing;
    R Saha and R K Ray; Met Trans A; Vol. 40, Issue 9 (2009); pp. 2160-2170

49. Adhesion of tire bead wire to rubber: some findings;
    H Pathak, R Mishra, S Mahajan, V Sridhar, N Bandyopadhyay and S Sunder; Wire Journal International; September (2009); pp. 89-91

50. Effect of high temperature oxide scale on steel surface for electrodes nickel plating process and characterization of coatings;
    M Manna; Surface and Coatings Technology; Vol. 204 (2010); pp. 1842-1846

51. Effects of ageing on the mechanical properties of directly quenched copper bearing microalloyed steels;
    S K Ghosh, A Haldar and P P Chattopadhyay; Materials Chemistry and Physics; Vol. 119, Issue 3 (2010); pp. 436-441

52. Effects of Cu addition on the synergistic effects of Ti-B in thermodynamically processed low carbon steels;
    S K Ghosh, N Bhowmik, A Haldar and P P Chattopadhyay; Materials Science and Engineering A; Vol. 527 (2010); pp. 1082-1088

53. Application of water based TiO2 nano-fluid for cooling of hot steel plate;
    S Chakraborty, A Chakraborty, S Das, T Mukherjeem D Bhattarcharjee and R K Ray; ISIJ International; Vol. 5, Issue 1 (2010); pp. 124-127

54. Texture and grain growth characteristics in a boron added interstitial free steel after severe cold rolling and annealing;
    R Saha and R K Ray; Materials Science and Engineering A; Vol. 527, Issue 78 (2010); pp. 1882-1890

55. Electroless nickel coating kinetics on TMT rebar surface and coating characterization;
    M Manna and N Bandyopadhyay; ISIJ International; Vol. 50, Issue 4 (2010); pp. 556-560

56. On mechanism of fatigue fracture in interstitial free steel sheet;
    S Majumdar, D Bhattarcharjee and K K Ray; Materials Science and Technology; Vol. 26, Issue 4 (2010); pp. 493-500