FY 05-06

1. Prediction of deoxidation and inclusion precipitation in semi-killed steel;
   S K Choudhary, S Chandra and A Ghosh; Met Trans B; Vol. 36B (2005); pp. 59-66

2. The physical chemistry of thermal decomposition of South African chromite minerals;
   V Tathavadkar, M P Anthony and A Jha; Met Trans B; Vol. 36B (2005); pp. 75-84

3. CFD modeling of hydroclone – prediction of cut size;
   M Narasimha, R Sripriya and P K Banerjee; Int. Journal of Mineral Processing; Vol. 75 (2005); pp. 53-68

4. Recovery of metal from slag/mixed metal generated in ferroalloy plants – a case study;
   R Sripriya and Ch V G K Murty; Int. Journal of Mineral Processing; Vol. 75 (2005); pp. 123-134

5. Scaling estimations of thermal and flow field in gas stirred ladles;
   S Ganguly; Met Trans B; Vol. 36B (2005); pp. 541-546

6. Numerical investigation of fluid flow phenomenon in a curved shape tundish of billet caster;
   A Tripathi and S K Ajmani; ISIJ International; Vol. 45 (2005); pp. 1616-1625

7. Oxide scale characterization of hot rolled coils by Raman spectroscopy technique;
   A Chattopadhyay, N Bandyopadhyay, A K Das and M K Panigrahi; Scripta Materialia; Vol. 52 (2005); pp. 211-215

8. Mathematical modeling of jet finishing process for hot-dip zinc coatings on steel strip;
   P Naphade, A Mukhopadhyay and S Chakrabarti; ISIJ International; Vol. 45 (2005); pp. 209-213

9. Improvement in surface brightness and prediction of spangle formation time in a continuous galvanizing line through heat balance;
   M Dutta, S Ganguly, G Jha, A K Singh, S Chakrabarti and N Rajesh; ISIJ International; Vol. 45 (2005); pp. 366-372

10. Use of flow barriers to eliminate vortex in the flow field generated in a continuous galvanizing bath;
    S K Dash, M Dutta and N Rajesh; ISIJ International; Vol. 45 (2005); pp. 1059-1065

11. Strain induced precipitation of complex carbo-nitrides in Nb-V and Ti-V microalloyed steels;
    A Pandit, A Murugaiyan, A S Poddar, A Haldar, D Bhattacharjee, S Chandra and R K Ray; Scripta Materialia, Vol. 53 (2005); pp. 1309-1314

12. Effect of filler alloys on heat affected zone cracking in preweld heat treated IN-738 LC gas-tungsten-arc welds;
    K Banerjee, N L Richards and M C Chaturvedi, Met Trans A, Vol. 36A (2005); pp. 1881-1890

13. Cold model studies of heat and mass transfer in steel making vessels;
    S K Ajmani and A Chatterjee; Iron Making and Steel Making; Vol. 32, Issue 6 (2005); pp. 515-527

14. Prediction of silicon content in blast furnace hot metal using Partial Least Squares (PLS);
    T Bhattacharya; ISIJ International; Vol. 45, Issue 12 (2005); pp. 1943-1945

15. Mathematical modeling of roll cooling and roll surface stress;
    J K Saha, S Chandra, S Kundu, S K Sinha, U Singhal and A K Das; ISIJ International; Vol. 45, Issue 12 (2005); pp. 1641-1650

16. Effect of coke micro-textural and coke petrographic properties on coke strength characteristics;
    R Sharma, P S Dash, P K Banerjee and D Kumar; ISIJ International; Vol. 45, Issue 12 (2005); pp. 1820-1827

17. Laboratory scale investigation to improve the productivity of stamp charge coke oven through optimization of bulk density of coal cake;
    P S Dash, S H Krishnan, R Sharma, P K Banerjee and S K Haldar; ISIJ International; Vol. 45, Issue 11 (2005); pp. 1577-1586

18. Effect of finish hot rolling temperature on the surface quality of galvannealed IF-HS steel sheets;
    S D Bakshi, M Dutta and D Bhattacharjee; ISIJ International; Vol. 45, Issue 9 (2005); pp. 1368-1370

19. A generalized formulation of latent heat functions in enthalpy based mathematical models for multicomponent alloy solidification systems; S Ganguly and S Chakraborty; Met Trans B; Vol. 37B (2006); pp. 143-145

20. Use of a multi-sensor technique to monitor the mould oscillation in a continuous billet caster;
    P P Sahoo and S Basu; ISIJ International; Vol. 46, Issue 2 (2006); pp. 219-225

21. Roll wear prediction model for finishing stands of Hot Strip Mill;
    S John, S Sikdar, A Mukhopadhyay and A Pandit; Ironmaking and Steelmaking; Vol. 33, Issue 2 (2006); pp. 169-175

22. Optimization of work roll shifting and bending to roll thinner gauge HR coils using genetic algorithm;
    S John, A Mukhopadhyay and S Sikdar; Ironmaking and Steelmaking; Vol. 33, Issue 2 (2006); pp. 67-73

23. Experimental simulation and mathematical modeling of air bubble movement in slab caster mold;
    V Singh, S K Dash, J S Sunita, S K Ajmani and A K Das, ISIJ International; Vol. 46, Issue 2 (2006); pp. 210-218

24. Analysis of a laboratory jigging system for improved performance;
    A K Mukherjee, V K Dwivedi and B K Mishra; Minerals Engineering; Vol. 18 (2005); pp. 1037-1044

25. Effect of drain cover on entrapment of air while draining a cylindrical vessel;
    S K Ajmani, S S Mondal and S K Dash; Numerical methods for heat and mass transfer; Vol. 15, Issue 4 (2005); pp. 394-414

26. Numerical simulation of transport phenomena in electromagnetically stirred semi-solid materials processing;
    J Chowdhury, S Ganguly and S Chakraborty; Journal of Physics D: Applied Physics; Vol. 38 (2005); pp. 2869-2880

27. Textural development in a extra low carbon steel during warm cooling;
    A Haldar and R K Ray; Materials Science and Engineering A; Vol. 391 (2005); pp. 402-407

28. Effect of cooling condition after warm cooling on the development of microstructure in an ELC steel;
    A Haldar, R K Ray and A J Khan; Solid State Phenomena; Vol. 105 (2005); pp. 259-264

29. Prediction of mechanical properties of hot rolled low carbon steel strips using artificial neural networks;
    A Mukhopadhyay and A Iqbal; Materials and Manufacturing Processes; Vol. 20 (2005); pp. 1-20

30. Finite elements modeling of the effects of roll gap geometry in hot rolling;
    A Mukhopadhyay, I C Howard and C M Sellars; Materials Science and Technology; Vol. 21, Issue 8 (2005); pp. 901-911

31. Regulating crown and flatness during hot rolling: A multiobjective optimization study using genetic algorithms;
    A Mukhopadhyay, R Nandan, R Rai, R Jayakanth, S Moitra and N Chakbarti; Materials and Manufacturing Processes; Vol. 20 (2005); pp. 1-21

32. Numerical treatment of diffusional phase transformation through implicit control volume method;
    A K Verma, S Chandra and B K Dhindaw; Materials Science and Technology; Vol. 21, Issue 11 (2005); pp. 1303-1308

33. Implementation of an online run-out table model in a Hot Strip Mill;
    A Mukhopadhyay and S Sikdar; Journal of Materials and Processing Technology; Vol. 169 (2005); pp. 164-172

34. Prevention of micro-flow marks in Cathodic Electro-Deposited (CED) primer coating in automotive industries: A Case study;
    T K Rout, P P Sahoo and D Deshpande; Material Performance; January Issue (2006); pp. 32-36

35. Application of image processing and radial basis neural network techniques for ore sorting and ore classification;
    V Singh and S M Rao; Minerals Engineering; Vol. 18 (2005); pp. 1412-1420

36. A fully implicit fixed grid finite difference formulation for phase change problems;
    A K Verma, S Chandra and B K Dhindaw; Trans. Indian Institute of Metals; Vol. 58, Issue 4 (2005); pp. 517-523

37. Numerical treatment of galvannealing process;
    A K Verma, S Chandra, B K Dhindaw and R D K  Misra; Materials Science and Technology; Vol. 418A (2006); pp. 335-340

38. An improved model for predicting limiting drawing ratio;
    R K Verma and S Chandra; Journal of Materials Processing Technology; Vol. 172 (2006); pp. 218-224

39. Mathematical modeling of volatile matter evolution during carbonization in metallurgical coke ovens;
    S K Das, K M Godiwalla, S P Mehrotra, S H Krishnan and P C Choudhary; High Temperature Materials and Processes; Vol. 24, Issue 5 (2005); pp. 301-314

40. Evidence of pyrolysis of resinite in coal through thermal maturation vis-à-vis hydrocarbon generation:
    An example from the Oligocene coals of Upper Assam, Northeast India; M P Singh and A K Singh; J. Geological Society of India; Vol. 65, Issue 6 (2005); pp. 238-244